The Thermal Shutdown Circuit detects overheating of the regulator if the output pin (VOUT) is shorte...

Inrush current is a large current that temporarily flows when a linear regulator (LDO regulator) sta...

Output noise is the noise generated by the linear regulator (LDO regulator) IC itself.

The reverse current protection function prevents current from flowing from the output to the input s...

Soft-start is function for slowly starting the output power. ABLIC's products are available with ou...

PSRR is an acronym for Power Supply Rejection Ratio. it refers to the ability to block the transmiss...

Over Current protection is a protection circuit that turns off the output when a large current flows...

The manual reset function is a function that can forcibly output a reset signal by inputting a signa...

The supply voltage divided output is a function that divides the sense pin voltage (Vsense) of the r...

The supply voltage divided output is a function that divides the input voltage (Vin) of the regulato...

The supply voltage divided output is a function that divides the input voltage (Vin) of the regulato...

The discharge shunt function compresses the output voltage fall time during power-off. The discharge...

Output voltage external setting is a function that sets the output voltage by using an external feed...

The following is an example of Watchdog trigger time Min, Typ, and Max by CDLY capacity. Refer to "2...

The following is an example of release delay time Min, Typ, and Max by CDLY capacity. Refer to "2. R...

The spread spectrum function modulates the switching frequency to broaden the frequency distribution...

Synchronous rectification is a switching regulator technology that increases efficiency by synchrono...

PWM is an acronym for Pulse Width Modulation. PWM method controls the output voltage by varying the ...

The "detection delay time" refers to the time from when the voltage of the monitored object falls be...

The voltage input to the SENSE pin, not the supply voltage of the reset IC, is monitored and detecte...

The following is an example of Watchdog trigger time Min, Typ, and Max by CDLY capacity. Refer to "2...

The following is an example of release delay time Min, Typ, and Max by CDLY capacity. Refer to "2. R...

The following is an example of Watchdog output "L" time Min, Typ, and Max by CDLY capacity. Refer to...

The following is an example of Watchdog trigger time Min, Typ, and Max by CDLY capacity. Refer to "2...

The following is an example of release delay time Min, Typ, and Max by CDLY capacity. Refer to "2. ...

The following is an example of Watchdog output "L" time Min, Typ, and Max by CDLY capacity. Refer to...

The following is an example of Watchdog double-pulse detection time Min, Typ, and Max by CDLY capaci...

The following is an example of Watchdog output "L" time Min, Typ, and Max by CDLY capacity. Refer t...

The cell-balance function is a feature that corrects the voltage imbalance among individual cells co...

Power-saving function is a function that forcibly stops discharging by inputting an external signal ...

The S-19212 Series recommends an output capacitance of 1μF or more. We've confirmed that the device ...

The ON/OFF should be connected directly to the VIN pin. Connecting the ON/OFF pin via a resistor is ...

The S-19212 Series does not require an external current limiting resistor.

The manual reset function is a function that can forcibly output a reset signal by inputting a signa...

The INT pin output function monitors the IC status and outputs a signal from the INT pin of the Nch ...

The BS pin is for accurately monitoring the cell voltage. As the charging and discharging currents i...

There are no issues with using the NC pin left open.

There are no operational issues as long as the SENSE pin voltage rises either at the same time as, o...

If the resistance values of the external voltage dividing resistors (Rup, Rdown) connected to the SE...

The frequency range that affects the stability of the IC is 1kHz to 10MHz. Please ensure that the ES...

The S-19509 Series is not ASIL-compliant on its own, as it is a product developed under QM (Quality ...

A reverse current from VOUT to VIN does occur through the parasitic diode inside the IC, but this wi...

We recommend an input capacitance (CIN) of 1.0μF or more.

The frequency range that affects the stability of the IC is 1kHz to 1MHz. Please ensure that the ESR...